CLEAN & OIL CUSTOMER GUN
Complete stripping of gun, cleaning of all parts, checking for wear & making suggestions to a customer of services needed to put gun in A-1 condition.
METAL FINISHING
Bluing -
Wire wheel Matte finish (Hunter finish)
- Rifle-semi auto 175.00
-Rifle-Bolt action 150.00
-Shotgun 150.00
-Handgun-semi-auto 150.00
-Handgun-revolver 125.00 Bead blast finish- ADD $ to above Rates 35.00
Slow rust bluing - ADD $ to above Rates 45.00
Oxynate 84 or KG Kote for stainless & Win 94's - ADD $ to above Rates 50.00 Parkerizing - MIL SPEC Finish , - Add to Bluing rate 50.00
WE DO NOT DO HIGH GLOSS BLUE < ONLY NON GLARE & MATTE FINISHES
INDUSTRY STANDARD GUNSMITH SHOP PRICES
Sight in customer gun (ammo not included) 50.00
Bore sight customer gun 15.00
Pattern Shotgun (ammo & targets not included) 50.00
Drill & Tap receiver for sights or Mount - PER HOLE 25.00 75.00
Cut dovetail in barrel for sight 45.00 75.00
INSTALL front sight ramp-
-Sweat on type 75.00
-Screw on type ( must drill & tap) 50.00
-Band type 75.00
PISTOL - Install insert in pistol sight 35.00
Build up or construct EXTRA HIGH pistol front sight 55.00
SHOTGUN - Install mid or front bead sight 35.00
- Plug hole & re-drill for bead sight 45.00
INSTALL RECEIVER SIGHTS
- Gun drilled & tapped 35.00
SCOPE MOUNTING
- Includes Mounting, checking scope & bore sighting
- Gun drilled & Tapped 35.00
- Gun NOT drilled & Tapped $ 75.00 125.00
GENERAL BARREL, ACTION & RIFLE WORK
Test fire customer gun ( AMMO EXTRA ) 35.00
Check headspace 15.00
Check firing pin protrusion 15.00
Make chamber cast 35.00
Remove fired case ( struck case ) from chamber 45.00
REMOVE LIVE ROUND from chamber 50.00
Remove obstruction from bore 35.00
Remove fouling from barrel 45.00
Lap barrel 75.00
Install liner in barrel ( liner & rebluing EXTRA ) 150.00
CUT & CROWN BARREL
- Rifles & shotguns 75.00 125.00
- Handguns 75.00
CHAMBER & FIT BARREL TO ACTION Hunting Match
- Does NOT include cost of barrel, or refinishing/bluing 150.00 275.00
Install Military Barrel, M1A, M-14, M1Carbine, Lee Enfields etc, 175.00 270.00
Lap in bolt handle 75.00 125.00
Welding on new bolt handle 75.00 175.00
Forging existing blot handle 75.00
MAKE & INSTALL SPRINGS
- Flat spring 35.00 75.00
- "V" spring 40.00 80.00
- Coil springs 45.00 85.00
SAFETIES- INSTALLING
Dakota, M-70 type etc 75.00 200.00
Mark-II Type 40.00 85.00
Chapman, Delorge, swing type 90.00 250.00
TRIGGERS, INSTALLING, ADJUSTING
Timiney, Dayton Triaster etc 50.00 80.00
Double set or single set 85.00 250.00
MATCH TRIGGERS< ANY BRAND ( HIGH end if - 8 lbs ) 75.00 150.00
Resolder rib ( not including re-bluing ) 75.00 225.00
Raising dent in Barrel ( or tube mag ) 50.00 100.00
Sleeve Barrel 75.00 125.00
Polish Chamber / Bore 35.00 75.00
REVOLVER ACTION JOB
- Clean & smoothen action ( NOT incl replacement parts ) 70.00 180.00
Rebarrel revolver ( labor only ) 100.00 180.00
Staighten crane on Revolver 45.00 75.00
Install crane lock 35.00
Remove or modify Revolver hammer spur 45.00
SEMI AUTO ACTION JOB
- Clean & smoothen action, NOT incl replacement parts 75.00 200.00
- Fit new hammer 45.00 85.00
- Fit new grip safety 50.00 95.00
- Fit any other new part 35.00 75.00
- Install auto pistol compensator 195.00 350.00
- Simple pattern 125.00 195.00
- Complicated pattern 195.00 295.00
- STIPPLING 150.00
GLASS / STEEL BEDDING BARREL & OR ACTION
- Hunting rifle 150.00 175.00
- Match rifle or complicated ( M-14, M-1 etc ) 175.00 350.00
- Pillar bed 150.00 350.00
Install recoil pad 35.00 75.00
Install sling swivels 35.00
Install recoil reducer 35.00 95.00
Inletting & finishing of semi-finished stock
- NOT incl checkering, butt pad, grip cap or other attachments 140.00 235.00
Fit, bed & finish synthetic stock 65.00 225.00
Fit action to Pre-finished synthetic stock 65.00 180.00
Camo painting stock 75.00 350.00
HUNTER FINISH
- Oil finish on average stock 75.00
- Same finish but on complicated stock or 2 piece stock 135.00
GUNSMITH FINISH
- Filled, hand rubbed finish on average stock 110.00
- Same finish on complicated stock 150.00
SPRAY FINISH
- Lacquer or polyurethane 95.00 175.00
RE-CUTTING CHECKING / CUTTING
All prices in Canadian funds and subject to applicable taxes.
Does NOT include return shipping.
DEACTIVATION
*** Includes letter of deactivation / Non proof ability
Machineguns & Cannons 200.00 500.00
Semi auto rifles 175.00 225.00
Bolt action rifles 125.00 175.00
Shotguns semi or pump 150.00 175.00
Submachine guns 150.00 175.00
Handguns - Semi autos 125.00 175.00
Handguns - Revolvers 200.00 275.00
MUZZLE THREADING / FLASH HIDERS / MUZZLE COMPENSATORS
From Tactical rifles & Carbines to softening the blast & recoil from your favorite hunting rifle, we have a variety of compensators to suit your needs.
We can shorten your long barreled rifle to a more manageable length, or shorten your AR-15 rifle to a Carbine length, move the gas block & install a custom muzzle brake.
Give us a call, we custom build to suit you!
We stock Vortex, Phantom, Vias, Krinkov, & Armalite
Pull ball from barrel 45.00 90.00
Remove broken ramrod from barrel 50.00
Re-Harden frizzen on flint lock 35.00
Remove breech plug 45.00
BASIC FEES Price Range
Per Man Hour 35.00 95.00
Per Man & Machine Hour 45.00 125.00
Minimum Charge Per Job 35.00
Written Appraisals & Cost Esimtes 75.00 75.00
Lathe turning of bolt 35.00 95.00
Lathe turning of small parts 45.00 55.00
Metal checkering 45.00 155.00
Draw filing 75.00 125.00
